Thin heat-resistant double-sided tapes series

We have a lineup of three double-sided adhesive tapes with a thin-film design and excellent heat resistance: Double-Face ™ R260, Double-Face ™ R310KS-2, and Double-Face ™ R380. Each is designed to be less than 50 μm in thickness, and can be used in various applications that require miniaturization and heat resistance of the entire product.

• Characteristics 
• Product Data
• Notes in Use
• Points to Note When Storing
• Featured Products

Characteristics 

• Double-Face ™ R260
  This is a double-sided tapes made by applying high-performance strong pressure sensitive adhesives to a thin special core material. It exhibits excellent performance for bonding various plastics, synthetic rubbers, metals, etc.
• Double-Face ™ R310KS-2
  In addition to demonstrating stable performance over a wide temperature range, the material design takes workability into account to reduce the pressure sensitive adhesives threading phenomenon and reduce the problem of glue return and glue skipping after processing. It can be used as a tape for fixing FPCs and electronic components.
• Double-Face ™ R380 Series
  It is a substrate-less tape and comes in two types of thicknesses: 30 μm and 50 μm. It is an adhesive tape with excellent heat resistance and maintains adhesive strength even in high-temperature environments, while reducing the misalignment of holding power. It is suitable for bonding heat-generating materials and heat dissipators, and can contribute to the miniaturization of products.

Product Data

• The above values are measured values and are not guaranteed values.
• Please contact our representative regarding your desired tape width and length.

Notes in Use

1. Clean the adherend (Remove dust, any other foreign particles, water, and oil.)
2. Make sure that the adherend is free of burrs and warpage.
3. Apply the tape to the adherend at a temperature of around 20 degrees centigrade wherever possible.
4. After applying the tape, press firmly.
5. Be sure to conduct a test before using the tape to check that the tape is suited for the application.

• These tapes are for industrial use only. Do not use them for the following applications.
  ･Applications that involve or may involve the direct attachment of the tape to the skin.
  ･Applications that involve the direct attachment of the tape to food.

Notes on strage

1. Store the product in a room away from sunlight. Keep it away from high temperatures and humidity. (The desirable temperature is 5 to 40 degrees centigrade, and the desirable humidity is 60% or lower.)
2. Avoid placing the product directly on the ground or floor. Place it on a table that allows air to pass through.
3. When storing tapes in a stack, be sure to insert a removable material, such as inserting paper, between the tapes and stack them vertically.

Featured Products

Environmentally friendlylow-VOC double-sided tapes Double-Face ™ R255

This is an environmentally friendly, toluene and formaldehyde free, double-sided tapes that removes toluene and formaldehyde from the raw materials

Thin heat-resistant double-sided tapes series

A lineup of thin film tapes with excellent heat resistance. Each adhesive tape is designed to have a thickness of 50μm or less, and can be used for various applications that require miniaturization of the entire product and heat resistance.

Heat-resistant slightly adhesive film LIOELM™ LE950 Series

This is a heat-resistant single-sided adhesive film made of acrylic pressure sensitive adhesives with low pollution and fine adhesive. It can be used as a carrier tape for FPC, electronic components, etc.

Base material joining tape (Splice tape)

This tape is used to bind (splice) substrates during printing/film processing. We have a lineup of products with features such as good adhesion in low-temperature environments, high-speed machining suitability, and high heat resistance.

Anti-tracking tape

This is an insulating tape for next-generation EVs that has both heat resistance (RTI 180℃) and tracking resistance (1000V). It can be used for insulating the housings of EV parts such as transformers/reactors, inverters/junction boxes, etc.

Removable protective film LIOELM™ LE501

A protective film with excellent transparency, reworkability, and air release properties. Can be used as surface protection for touch panel products, process protection, etc.