| Dry curing method |
UV curing type |
| Packing |
1kg |
| Purpose/Function |
Tubes, bottles, meter panels, amusements, displays, nameplates, packages, plastic moldings, books, insulation |
| Base material |
AC, PC, ABS, PVC, treated PET, treated PP, treated PE, paper, synthetic paper |
| Printability |
Leveling properties, curing properties, high speed printing properties |
| Post-processability |
Punching property |
| Paint film appearance |
luster |
| Paint film properties |
Abrasion resistance |
| Resistance |
Heat resistance, hot water-based resistance, weather resistance |
| Paint film strength |
Tough coating, flexibility, high hardness |
| Chemical Resistance |
Acid resistance, alkali resistance, alcohol resistance, solvent resistance, oil resistance, gasoline resistance, sunscreen resistance |
| Electrical properties |
Insulation |
| Characteristics (other) |
- Excellent adhesion to treated polyethylene and treated polypropylene bottles.
- Good reproducibility of gauze omissions, fine letters, and fine lines during high-speed printing.
- Due to its wide adhesion range, it can be applied to various base materials.
|
| Finish, texture, appearance effect |
Gloss (glossy) |
| setting color |
121S red, 151S red, 171S red, 193M red, 228 yellow, 231S yellow, 262S yellow, 037S indigo, 391S indigo, 516S vermilion, 791S grass B, 821S purple, 662S white, Conch 662 white, 662T white (thixotropy improved) product), 911S ink, S medium, S extender |
| Heat dry curing conditions |
Curing: 120W/cm metal halide lamp x 10m/min |
| Auxiliary agents, additives, cleaning solvents, etc. |
- FDSS water resistance additive――――Adhesion/ water-based improver
- FDSS320 Regiuser --- Viscosity modifier
- TU262FDSS thickener --- Viscosity modifier
- SS Plate Cleaner ECO Series...A plate cleaning agent for screen printing that does not fall under organic regulations or the PRTR law. SD is the standard type, and QD is even faster drying.
|
| How to use ink & precautions |
The ink can be used as is after stirring, but in the following cases, adjust the ink using an auxiliary agent.
- water-based
If the following requirements are met, please add 3% of "FDSS water resistance additive". If too little is added, sufficient water-based will not be obtained, and if too much is added, curing will be poor, so please be sure to follow the additive amount.
1) When it is difficult to maintain and manage the appropriate degree of frame treatment (balance of adhesion and water-based).
2) When the product is used in a high temperature and high humidity atmosphere (bathroom, kitchen, etc.).
3) If a pasteurizer (hot pack, hot shower wash, etc.) is used during the filling process.
4) When high content resistance is required.
Please note that the usable time after adding the additive is approximately 12 hours at room temperature, so please add the required amount to the ink.
This product gradually reacts with moisture in the air, so close it tightly after use and store it in a cool, dark place.
- Viscosity adjustment
*Appropriate amount of adjuvant used
・FDSS320 Regiuser: 3-10% added to ink
・TU262FDSS thickener: 0.5-1% added to ink
1) Temperature change
The viscosity of UV-curable inks is highly dependent on temperature, and especially at low temperatures, the viscosity (or tack) increases and the transferability of the ink decreases, so please use the FDSS320 Regulator together to adjust the viscosity. In addition, if thin lines, thick characters, or sagging occur, please adjust with TU262FDSS thickener.
2) Printing speed
The higher the printing speed, the lower the viscosity (tack) and the need for easier transfer.
As in 1) above, add Regiuser etc. depending on the metastatic state.
- storage
It polymerizes (gels) when exposed to ultraviolet light or heat, so please store it in a closed container in a cool, dark place with good ventilation (below 25℃).
- Adhesion between overprints
If the second color is printed after the first color underprint ink has been cured excessively, the adhesion between the inks may be insufficient. In that case, please adjust the UV lamp output to adjust the degree of curing of the underprint ink.
|
| Physical properties |
|
| Requests for use |
- This document is an example of our test data, and the properties obtained will vary depending on printing/processing conditions, base materials, etc., and are not guaranteed.
Before using the product, please carefully check its intended use.
- Before handling this product, be sure to read the "Product Safety Data Sheet" and handle with care.
- If you wish to export this product overseas, please be sure to check with us.
|
